helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software enables simple helical bevel gear reducer interactive product selection of the entire gearbox and gear-engine system. Cat4CAD supports you in choosing and configuring the products, provides you the opportunity to print out intensive technical data bedding, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sized sizes.
Multiple Input Options: Essential gear motors, ” or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, mounting pilots and flanges offer a wide selection of design solutions.
UNIBLOCK Housing: For maximum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to simply accept brakes, encoders or pressured cooling.
High efficiency engine design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals upon heat treated, plunge floor shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors are available in three phase high efficiency styles through 50 HP and single phase to 5 HP. We provide a variety of input and result shaft choices. Additionally, you will see fixed and variable swiftness motors and range of ratios available in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Critical dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying demands of customers, we offer a wide range of Helical Bevel Gear Reducers. The technological content of our products allows for an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully found in a multitude of commercial and civil applications. These are B-Series units which offer excellent value for money and output torque/weight ratio, especially due to the fact they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for motor coupling, IB with input shaft, CB with compact motor, PB-fitted for engine coupling with flexible joint
Casing with feet FC, flange SC and universal UC
Power up to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second reduction stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM evaluation and input and result flanges of grey cast-iron G200 to ensure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, result shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced output, assemble/disassemble kit
Series EP right angle helical bevel gear motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and may be offered with single or dual extended output shafts.
Units are also available because shaft mounted or with result flanges and are designed for installation horizontally or vertically. The models can also be offered with a bolt on torque response bracket and all variants can be found either motorised or with an insight shaft assembly.
Adding to the brand new selection of Ever-Power helical equipment motors this product takes benefit of our a long time of accumulated design experience together with the use of high quality materials and components. The end result is a number of velocity reducing geared motors offering high load transporting capacities, increased efficiency, calm running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double essential oil seals, on input and output shaft as required.
All products are dimensionally interchangeable with additional major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be fitted with a backstop module and reducer Products can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic and automation etc.
Key Features:
Sizes: A40-A50-A70
Available versions: EP – fitted for engine coupling, IEP – with input shaft, CEP – with small motor
Cases with feet, flange or universal
Switch on to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and composed of Y series engine, helical gear,Arc gear and worm gear. The gears are made from high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, fine appearance ,and solid capacity of being overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to since high since 96% with low energy consumption, strong adaptability and is with the capacity of operating continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.

Tags

Drive Chain

As one of leading drive chain manufacturers, suppliers and exporters of mechanical products, We offer drive chain and many other products.

Please contact us for details.

Mail:sales@drivechain.top

Manufacturer supplier exporter of drive chain.

Recent Posts